MIKROE-2046 WIFI 7 CLICK ATWINC1500-MR210PB

  • Mã sản phẩm: MIKROE-2046 WIFI 7 CLICK ATWINC1500-MR210PB
  • Nhà sản xuất: MIKROE
  • Website hỗ trợ: https://www.proe.vn
1.190.000₫

WiFi 7 click carries the ATWINC1510-MR210PB IEEE 802.11 b/g/n module, specifically optimized for low-power IoT applications. The click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over SPI interface, with additional functionality provided by the following pins on the mikroBUS™ line: PWM, INT, RST.

 

ATWINC1510-MR210PB FEATURES

 

The ATWINC1510-MR210PB is a low-power consumption 802.11 b/g/n module which is specifically optimized for low-power IoT applications.

The module has a Cortus APS3 32-bit processor. This processor performs many of the MAC functions, including but not limited to association, authentication, power management, security key management, and MSDU aggregation/de-aggregation. In addition, the processor provides flexibility for various modes of operation, such as STA and AP modes.

MODULE CURRENT CONSUMPTION

The table below describes the current consumption of the ATWINC1510-MR210PB module:

Device state Code rate Output power, dBm Current consumption(1)
IVBATT IVDDIO
ON_Transmit 802.11b 11Mbps 20.5 290mA 22mA
802.11b 11Mbps 19.5 294mA 22mA
802.11g 6Mbps 19.5 292mA 22mA
802.11b 54Mbps 17.5 250mA 22mA
802.11n MCS 0 18.0 244mA 22mA
802.11n MCS 7 15.5 289mA 22mA
ON_Receive 802.11b 1Mbps N/A 52.5mA 22mA
802.11b 11Mbps N/A 52.5mA 22mA
802.11g 6Mbps N/A 55.0mA 22mA
802.11b 54Mbps N/A 57.5mA 22mA
802.11n MCS 0 N/A 54.0mA 22mA
802.11n MCS 7 N/A 58.5mA 22mA
ON_Doze N/A N/A 380µA <3.5µA
Power_Down N/A N/A <0.5µA <3.5µA

 

ADDITIONAL PINS

 

Additional pins on the WiFi 7 click, besides the ones on the mikroBUS™ line:

SPECIFICATIONS

 

Type WiFi
Applications Optimized for low power IoT applications
On-board modules ATWINC1510-MR210PB
Key Features IEEE® 802.11 b/g/n 20MHz solution, integrated PCB antenna, supports IEEE 802.11 WEP, WPA, WPA2 Security
Interface GPIO,SPI
Compatibility mikroBUS
Click board size M (42.9 x 25.4 mm)
Input Voltage 3.3V

 

PINOUT DIAGRAM

This table shows how the pinout on WiFi 7 click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
  NC 1 AN PWM 16 EN Module Enable
Active-Low Hard Reset RST 2 RST INT 15 INT Device Interrupt output
Chip select CS 3 CS TX 14 NC  
SPI Clock SCK 4 SCK RX 13 NC  
SPI Master Input Slave Output MISO 5 MISO SCL 12 NC  
SPI Master Output Slave Input MOSI 6 MOSI SDA 11 NC  
Power supply +3.3V 7 3.3V 5V 10 NC  
Ground GND 8 GND GND 9 GND Ground

PROGRAMMING

Code examples for WiFi 7 click, written for MikroElektronika hardware and compilers are available on Libstock.

CODE SNIPPET

The following code snippet shows the default main function for all examples.

01 void main(void)
02 {
03     systemInit();
04     printf("Project built for Click Boardrn");
05     printf("Starting driver initialization...rn");
06     
07     hal_wifi7_init();
08     m2m_wifi_init();
09     while (1)
10     {
11         ApplicationTask();
12         m2m_wifi_task();
13     }
14 }

RESOURCES

 Click boards™ Standard Page

 mikroBUS™ Standard specification

 Click board catalog

DOWNLOADS

 WiFi 7 click example on Libstock

 WiFi 7 click schematic

 ATWINC1510-MR210PB datasheet

 WiFi Click boards™ guide

Xem thêm Thu gọn

Điện tử ProE cung cấp linh kiện điện tử, thiết bị điện tử , linh kiện IoT chính hãng. ProE cung cấp dịch vụ đặt hàng linh kiện điện tử, thiết bị điện tử chính hãng theo yêu cầu cụ thể của khách hàng. Liên hệ : contact@proe.vn, SĐT: 0938946849
Website: www.proe.vn
Diễn đàn: https://www.facebook.com/groups/278263459284765/
Youtube Chanel: ProE Youtube
Facebook: ProE Facebook

Sản phẩm vừa xem

popup

Số lượng:

Tổng tiền:

Giỏ hàng( Sản phẩm)

0974350095