C2000 Piccolo MCU F280049C LaunchPad™ development kit

  • Mã sản phẩm: LAUNCHXL-F280049C
  • Nhà sản xuất: Texas Instruments
  • Website hỗ trợ: https://www.proe.vn


To get started developing:
Step 1: Buy the C2000 MCU F280049C Launchpad
Step 2: See the “Get Started” section below
LAUNCHXL-F280049C is a low cost evaluation and development tool for the F28004x series (including InstaSPIN-FOC capability) in the TI MCU LaunchPad ecosystem which is compatible with various plug-on BoosterPacks (suggested under the Recommended BoosterPacks in the Features section below). This extended version of the LaunchPad supports the connection of two BoosterPacks. The LaunchPad provides a standardized and easy to use platform to use while developing your next application.


Hardware Features

  • TMS320F280049C: 100 MHz C28x CPU with FPU and TMU, 256 KB Flash, InstaSPIN-FOC enabled, 3x 12-bit ADC, CAN, encoder, FSI, UART, and more
  • On-board XDS110 debug probe for real-time debug and flash programming
  • 80 pin LaunchPad leveraging the BoosterPack ecosystem
  • Power domain isolation for real-time debug  and flash programming
  • Isolated CAN transceiver
  • Two encoder interface connectors
  • FSI interface connector
  • Hardware Files are in C2000Ware at boards\LaunchPads\LAUNCHXL_F280049C


Software Features

Recommended BoosterPacks


Get Started

  • For InstaSPIN-FOC
  • For non-InstaSPIN
    • Install Code Composer Studio IDE and C2000Ware.
    • Connect the LaunchPad using the included Micro USB cable to a computer
    • Open a serial terminal program of your choice (Putty, HyperTerm, etc.) and configure it to access the LaunchPad virtual COM port with 115200 Baud, 8-bit data, No parity, and single stop Bit. The COM port number can be found by opening your computer’s Device Manager
    • Ensure that the XDS110's second port is a serial port. Refer to the XDS110 Wiki for the configuration details
  • When connected to your computer, the LaunchPad will power up and flash the red and blue LEDs for approximately 3 seconds. After the LEDs complete flashing, the LaunchPad will enter an ADC sample mode
  • The terminal will display the latest ADC sample reading based on ADCINA5 (Pin 23 of the BoosterPack header) at a one second interval
    • If the sample is below mid-scale (1.5V/2048) the green LED (LED5) will light
    • If the sample is above mid-scale the red LED (LED4) will light
  • Build and load other examples in C2000Ware
  • Ask questions on the TI C2000 e2e forum

What's Included

  • Piccolo F280049C Launchpad
  • Micro USB cable
  • Quick Start Guide
Xem thêm Thu gọn

Điện tử ProE cung cấp linh kiện điện tử, thiết bị điện tử , linh kiện IoT chính hãng. ProE cung cấp dịch vụ đặt hàng linh kiện điện tử, thiết bị điện tử chính hãng theo yêu cầu cụ thể của khách hàng. Liên hệ : contact@proe.vn, SĐT: 0938946849
Website: www.proe.vn
Diễn đàn: https://www.facebook.com/groups/278263459284765/
Youtube Chanel: ProE Youtube
Facebook: ProE Facebook

Sản phẩm vừa xem


Số lượng:

Tổng tiền:

Giỏ hàng( Sản phẩm)