The N100-v9 case is compatible with both Jetson Nano A02 and B01 version now.(NEW)
[NVIDIA Jetson Nano Metal Case, Model: N100
This is a metal case specially designed for NVIDIA Jetson Nano Developer Kit, and it supports power switch and reset switch, and it's reserve the GPIO hole and the installation space of the fan, and easily assemble it.
we recommend that you read the introduction to the power supply in the official documentation before you assemble this case, thus you can understand deeply this case.
Note: The NVIDIA Jetson Nano Developer Kit and antenna are not included, and the 4-pin cooling fan is not included aslo!
Please refer toGeekworm N100-V9 User Manual
1) There are two jumper caps in the screws pack. ①Because this case has a power control switch, you need to disable the AUTO ON function firstly. Please insert one jumper cap into the “AUTO ON” position of the J40 pin to disable the AUTO ON function. ②Another Jumper cap is used to toggle the power supply between Micro USB and DC Jack. Insert this jump cap in "J48" Pin to disable Micro USB PWR to power (enable the DC 5V 4A jack PWR). The power control switch should be insert into “ON” pin at J40. And the blue and white cable of power control switch need to be insert in “3.3V” and “GND” pin at J41.
2) The reset switch should be insert in “RST” pin at J40. Please refer to the photo3 at the back.
3) A camera bracket is added for raspberry pi official camera, can fix the camera on the top or side of the case, adjust the camera position as your requirement. Please refer to the photo1 at the back.
The case is reserve 22mm high fan installation height , it is recommend to use Noctua NF-A4x20 5V PWM fan, we prepair 4 pcs PM2.5*22 screws and 4 pcs M2.5 nuts and 4 pcs gaskets to install this fan. You need to use the ABS tweezers when you install this fan. Please see the video.
We provide a new camera bracket to setup the camera although you can also mount the camera on the rear panel of the case. Since we don't know the camera you are using, so this bracket hole is only compatible with the size of the Raspberry Pi official camera. You can also choose the installation location of your camera bracket.
This Geekworm Jetson Nanno N100 case is also compatible with the NVIDIA Jetson Xavier NX developer kit, but you will need extra 2pcs WiFi Antenna with IPEX MHF4 to RP SMA Female Extension Cable to use together with N100.
To use the WiFi antennas, it need to remove the buttom holder of NVIDIA Jetson Xavier NX. Then install the antennas.
Installation video for NVIDIA Jetson Xavier NX: https://youtu.be/7Cqr9R04htc
This is a WiFi Antenna with IPEX MHF4 to RP SMA Female Extension Cable which can be used for NVIDIA Jetson Xavier NX developer kit. To use this WiFi antenna, it need to remove the buttom holder of NVIDIA Jetson Xavier NX. The Geekworm N100 case can also be used for install the NVIDIA Jetson Xavier NX developer kit, but you will need these extra 2pcs WiFi Antenna with IPEX MHF4 to RP SMA Female Extension Cable. To use this WiFi antenna, it need to remove the buttom holder of NVIDIA Jetson Xavier NX.
U.FL Cable Information
Q:How to assemble this case?
A: Please read the following picture or refer to wiki: raspberrypiwiki.com/index.php/N100
Q: Is it supported to install a fan?
A: Support for fan installation, 22mm high fan installation height reserved
Q: How do I use a jumper?
A: Because this case has a power switch, you need to disable the AUTO ON function first. Please insert the jumper cap into the AUTO ON position of the J40 pin to disable the AUTO ON function.
Q: Why was the MICRO SD card slot cancelled?
A: N100-V9 is compatible with both A02 and B01 versions now. We must increase the distance between the JETSON NANO motherboard and the front panel of the case to install the switch. We found that even if we kept the TF card slot, we couldn’t insert the TF card by hand or plastic tweezers, so we have to cancel this card slot; We hope that the official NVIDIA will adjust the position of J50 in subsequent versions. For more questions, please refer to the official forum link: https://forums.developer.nvidia.com/t/stop-shipping-the-nvidia-jetson-nano-development-kit-b01-j50-is-on-the-wrong-side/112066
Q: How to choose the right power supply?
A: JETSON NANO supports two kinds of interface power supply: Micro USB power adapter and DC Jack power adapter; You can choose different power adapter by controlling the jumper of J48; We strongly recommend that you use DC Jack PSU, because DC Jack can provides greater current input than Micro USB.
For Jetson Nano B01 version:
For Jetson Nano A02 version:
How to install the Geekworm NVIDIA Jetson Nano Metal Case for A02 version, please refer to: https://youtu.be/SpUB6h4Akp4
How to install the Geekworm NVIDIA Jetson Nano Metal Case for B01 version, please refer to: https://youtu.be/Q5n2Aa_z0qI
Điện tử ProE cung cấp linh kiện điện tử, thiết bị điện tử , linh kiện IoT chính hãng. ProE cung cấp dịch vụ đặt hàng linh kiện điện tử, thiết bị điện tử chính hãng theo yêu cầu cụ thể của khách hàng. Liên hệ : firstname.lastname@example.org, SĐT: 0938946849
Diễn đàn: https://www.facebook.com/groups/278263459284765/
Youtube Chanel: ProE Youtube
Facebook: ProE Facebook